The most commonly applied technique for the determination of the ash content and ash composition of coals and other solid fuels in the laboratory involves heating the fuel slowly in air to constant mass at a temperature of 815°C (1,500°C), and subjecting the resultant ash residue to chemical elemental analysis. The ash residue is normally weighed to provide an estimate of the ash content of the fuel, and then analyzed for the 10 major elements present in coal ashes, i.e., Si, Al, Fe, Ca, Mg, Ti, Na, K, P, and S. The elemental concentrations are conventionally expressed as oxides, in their highest oxidation states. The analysis of the laboratory-prepared ash for its trace element content is also fairly common practice. This is a perfectly reasonable and practical approach for most coals, and many other solid fuels, and has been applied for biomass ash analysis.
See also: Biomass.
Ash Content – Biomass
Ash content (which represents in inorganic content) of biomass is the inorganic oxides that remain after complete combustion of the feedstock. The amount of ash between different types of feedstocks differs widely (0.1% for wood up to 15% for some agricultural products) and influences the design of the reactor, particularly the ash removal system. The chemical composition of the ash is also important because it affects the melting behavior of the ash. Ash melting can cause slagging and channel formation in the reactor. Slag can ultimately block the entire reactor.
Generally, the ash-forming inorganic materials in most solid fuels, including biomass, can be divided into two broad fractions, viz: (i) the inherent inorganic material and (ii) the extraneous inorganic material.
The inherent inorganic material, which exists as part of the organic structure of the fuel, and is most commonly associated with the oxygen-, sulfur-, and nitrogen-containing functional groups. These organic functional groups can provide suitable sites for the inorganic species to be associated chemically in the form of cations or chelates. Biomass materials tend to be relatively rich in oxygen-containing functional groups, and a significant fraction of the inorganic material in some of the lower ash biomass fuels is commonly in this form. It is also possible for inorganic species to be present in fine particulate form within the organic structure of some of the fuels, and to behave essentially as an inherent component of the fuel.
The extraneous inorganic material, which has been added to the fuel through geological processes, or during harvesting, handling, and processing of the fuel. Biomass fuels, for instance, are commonly contaminated with soil and other materials, which have become mixed with the fuel during collection, handling and storage.
The most commonly applied technique for the determination of the ash content and ash composition of coals and other solid fuels in the laboratory involve heating the fuel slowly in air to constant mass at a temperature of 815°C (1,500°F), and subjecting the resultant ash residue to chemical elemental analysis. The ash residue is normally weighed to provide an estimate of the ash content of the fuel, and then analyzed for the 10 major elements present in coal ashes, i.e., Si, Al, Fe, Ca, Mg, Ti, Na, K, P, and S. The elemental concentrations are conventionally expressed as oxides, in their highest oxidation states. The analysis of the laboratory-prepared ash for its trace element content is also fairly common practice. This is a perfectly reasonable and practical approach for most coals, and many other solid fuels, and has been applied for biomass ash analysis.
Biomass feedstocks and fuels exhibit a wide range of physical and chemical properties (Table A-25), but despite the wide range of possible sources, biomass feedstocks are remarkably uniform in many of their fuel properties. However, nearly all kinds of biomass feedstocks destined for combustion fall in the range 6,450 to 8,200 Btu/lb). For most agricultural residues, the heating values are even more uniform – approximately 6,450 to 7,300 Btu/lb. The values for most woody materials fall into the range 7,750 to 8,200 Btu/lb.
The most commonly applied technique for the determination of the ash content and ash composition of coals and other solid fuels in the laboratory involves heating the fuel slowly in air to constant mass at a temperature of 815°C (1,500°F), and subjecting the resultant ash residue to chemical elemental analysis. The ash residue is normally weighed to provide an estimate of the ash content of the fuel, and then analyzed for the 10 major elements present in coal ashes, i.e. Si, Al, Fe, Ca, Mg, Ti, Na, K, P, and S. The elemental concentrations are conventionally expressed as oxides, in their highest oxidation states. The analysis of the laboratory-prepared ash for its trace element content is also fairly common practice. This is a perfectly reasonable and practical approach for most coals, and many other solid fuels, and has been applied for biomass ash analysis.
See also Ash, Ash Composition.
As-Received Moisture
The as-received moisture of a carbonaceous samples is the moisture present in a sample when delivered to the analytical laboratory or to the customer. Moisture content can affect the self-heating rate of the sample in two ways: changing the overall heat balance and the rate of the oxidation reaction.
It has been suggested that there is a critical moisture content at which the rate of oxidation reached a maximum, but the reaction may be subject