work. In fact, the leakage flux creates additional losses that make the coil less efficient, electromagnetically speaking (see Figure 1.1-6). The principles illustrated here become very important later on as we discuss the magnetic field in the generator and stray losses.
Figure 1.1-5 Representation of a magnetic field produced by the flow of electric current in a coil‐shaped conductor.
Figure 1.1-6 Representation of a magnetic field produced by the flow of electric current in a coil‐shaped conductor operating in air, showing the effective and leakage flux components of the magnetic field produced.
To use the flux produced in a coil as effectively as possible, highly permeable ferromagnetic materials are used to capture and direct the flux so that the amount of leakage flux is minimized. This allows the coil to do more useful work and keeps losses to a minimum. Iron in various derivatives is by far the most widely used material because it has all the magnetic characteristics required. It is structurally suitable, and cost‐effective. When an “iron” core is used within the coil, and current is flowing, the magnetic field produced is shaped effectively, and the iron core essentially becomes a north–south magnet in the process (see Figure 1.1-7). This is why stator cores and rotor poles of generators are made of steel, containing iron and a few small quantities of additional elements. The iron allows the principles discussed above to become a reality and is one of the reasons generators can be built to at least 97.5% efficiency.
Figure 1.1-7 Representation of a magnetic field produced by the flow of electric current in a coil‐shaped conductor with an “iron” core. The majority of the field produced is effective flux and the leakage field is reduced to a minimum.
1.1.2 Electricity
Electricity is the flow of positive or negative charges. Electricity can flow in electrically conducting elements (called conductors), or it can flow as clouds of ions in space or within gases. As will be shown in later chapters, both types of electrical conduction are found in hydro generators (see Figure 1.1-8).
Figure 1.1-8 Electricity. (I) Ionic clouds of positive and negative currents. The positive clouds are normally atoms that lost one or more electrons; the negative clouds are normally free electrons. This effect can be found inside the generator as partial discharge in the stator winding. (II) The flow of electrons inside a conductor material, for example, the copper windings of the rotor and stator.
Figure 1.2-1 Electrical–mechanical equivalence.
1.2 ELECTRICAL–MECHANICAL EQUIVALENCE
There is an interesting equivalence between the various parameters describing electrical and mechanical forms of energy. People with either electrical or mechanical backgrounds find this equivalence useful to the understanding of the physical process in either form of energy. Figure 1.2-1 describes the various forms of electrical–mechanical equivalence.
1.3 ALTERNATING CURRENT (AC)
Synchronous generators operate with both alternating‐current (AC) and direct‐current (DC) electric power. The DC can be considered a particular case of the general AC, with frequency equal to zero.
The frequency of an alternating circuit is a measure of the number of times the currents and/or voltages change direction (polarity) in a unit of time. The hertz (Hz) is the universally accepted unit of frequency, and measures cycles per second. One Hz equals one cycle per second. Alternating currents and voltages encountered in the world of industrial electric power are for all practical purposes of constant frequency. This is important because periodic systems, namely systems that have constant frequency and sinusoidal signals, allow the currents and voltages to be represented by phasors.
Figure 1.3-1 A phasor E that can represent the voltage impressed on a circuit.
A phasor is a rotating vector. The benefit of using phasors in electrical engineering analysis is that it greatly simplifies the calculations required to solve circuit problems.
Figure 1.3-1 depicts a phasor of magnitude E, and its corresponding sinusoidal trace representing the instantaneous value of the voltage quantity e. The magnitude E represents the maximum value of voltage (e).
The phasor is made of a vector with magnitude proportional to the magnitude of E, rotating at a constant rotational speed ω. The convention is that phasors rotate counterclockwise. The vertical projection of the phasor results in a sinusoid representing the instantaneous voltage (e) existing at any time. In Figure 1.3-1, α = ω × t, where t is the time elapsed from its zero crossing.
When a sinusoidal voltage is applied to a closed circuit, a current will flow in it. After a while, the current will have a sinusoidal shape (this is called the steady‐state current component) and the same frequency as the voltage. An interesting phenomenon in periodic circuits is that the resulting angle between the applied voltage and the current depends on certain characteristics of the circuit. These characteristics combine into one representative parameter, impedance and are broken down into resistive, capacitive, and inductive. The angle between the voltage and the current in the circuit is called the power factor angle and is defined as φ. The cosine of the same angle is called the power factor