the main impurity is pyruvic acid, representing 1–6% by weight of the metatartaric acid product, depending on preparation conditions (Table 1.18). It is therefore important to correct the esterification number to compensate for this impurity. The formation of these two acids results from the intramolecular dehydration of a tartaric acid molecule, followed by decarboxylation (Figure 1.19).
There are many laboratory tests for assessing the effectiveness of a metatartaric acid preparation. Table 1.19 presents an example of a procedure where a saturated potassium bitartrate solution is placed in 10 ml test tubes and increasing quantities of metatartaric acid preparations with different esterification numbers are added. This inhibits the precipitation of potassium bitartrate induced by adding 1 ml of 96% vol. ethanol and leaving the preparation overnight at 0°C. Only 1.6 mg of a preparation with an esterification number of 40.8 is required to inhibit crystallization, while 4.0 mg is necessary if the preparation has an esterification number of 26.6.
FIGURE 1.19 Impurities in metatartaric acid.
Metatartaric acid acts by opposing the growth of the submicroscopic nuclei around which crystals are formed. The large uncrystallized molecules of metatartaric acid get in the way during the tartrate crystal building process, blocking the “feeding” phenomenon, i.e. crystal growth. If the dose is too low, inhibition is only partial, and anomalies and unevenness are observed in the shape of the crystals.
TABLE 1.19 Inhibition of Potassium Bitartrate Precipitation by Various Metatartaric Acids (Peynaud and Guimberteau, 1961)
| Number | Esterification number | Metatartaric acid added to each tube (in mg) | |||||
|---|---|---|---|---|---|---|---|
| 0.4 | 0.8 | 1.6 | 2.4 | 3.2 | 4.0 | ||
| 1 | 40.8 | 12.0 | 15.8 | 17.2 | 17.2 | 17.2 | 17.2 |
| 2 | 38.2 | 12.0 | 15.6 | 17.2 | 17.2 | 17.2 | 17.2 |
| 3 | 37.3 | 12.0 | 15.3 | 17.2 | 17.2 | 17.2 | 17.2 |
| 4 | 33.4 | 9.6 | 12.0 | 16.3 | 17.0 | 17.2 | 17.2 |
| 5 | 31.5 | 8.6 | 11.0 | 15.3 | 15.9 | 16.5 | 17.2 |
| 6 | 26.6 | 7.9 | 10.5 | 12.7 | 15.0 | 16.0 | 17.2 |
| 7 | 22.9 | 6.4 | 7.6 | 11.2 | 13.6 | 15.6 | 16.8 |
The numbers indicate potassium remaining in solution (in mg) in each tube containing 10 ml of a saturated potassium bitartrate solution. The original amount was 17.2 mg.
The fact that metatartaric acid solutions are unstable has a major impact on their use in winemaking. They deteriorate fairly rapidly and are also sensitive to temperature. Hydrolysis of the ester functions occurs, accompanied by an increase in acidity. After 20 days at 18–20°C, there is a considerable decrease in the esterification number (Figure 1.20). Under experimental conditions, total hydrolysis of a 2% metatartaric acid solution takes three months at 23°C and 10 months at 5°C. Consequently, it is necessary to ensure that metatartaric acid solutions are prepared just prior to use in wine.
FIGURE 1.20 Hydrolysis rate of two grades of metatartaric acid in 2% solution (T = 18–20°C), followed by a decrease in the esterification number (Ribéreau‐Gayon et al., 1977).
Furthermore, the same phenomenon occurs in wine and is detrimental to the treatment's effectiveness. Ribéreau‐Gayon et al. (1977) demonstrated that stability in terms of tartrate precipitations may be considered effective for the following lengths of time, depending on temperature:
Several years at 0°C.
Over two years at 10–12°C.
One year to 18 months at temperatures varying between 10°C in winter and 18°C in summer.
Three months at 20°C.
One month at 25°C.
One week at 30°C.
A few hours between 35 and 40°C.
At first glance, metatartaric acid instability accounts for surprising observations concerning wines treated in this way. One sample, stored at 0°C in a refrigerator, had no precipitation, while calcium tartrate precipitation occurred in another sample stored at 20–25°C when it was no longer protected due to hydrolysis of the metatartaric acid.
The conditions for using metatartaric acid depend on its properties. A concentrated solution, at 200 g/l, should be prepared in cold water at the time of use. As metatartaric acid is strongly hygroscopic, it must be stored in a dry place.
Metatartaric acid is added after fining, as there is a risk of partial elimination due to flocculation. It is particularly affected by bentonite and potassium ferrocyanide treatments. Although there was some cause for concern that high‐temperature bottling would reduce the effectiveness of metatartaric acid, in fact, under the actual conditions of use, this bottling technique has little or no negative impact (Section 12.2.4). Incidentally, a slight opalescence may be observed after a wine has been treated, especially when the most efficient products, with high esterification numbers, have been used. It is therefore